pb14 fails on 32MB CF-Card

[Minol-Pirol]

Hello ,

I tried to update pb13.4 to pb14 with generic-pc image. The system is a GCT-Allwell STB3036 Set Top Box with NS Geode CS5530 chipset and a CF-Card reader connected to the secondary IDE-Master. The web-GUI update procedure was done successful, but every start results in a kernel panic message (unable to mount rootfs). After downgrade to pb13.4, all is fine again. :-( ?

The "log reverse sort order" option is missing in pb14.

[Michael]

pb13.4 worked but pb14 fails to find the rootfs? Is there any way you could post your "dmesg" output from pb13.4 or pb14?

[Minol-Pirol]

dmesg from pb13.4:

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p10 #0: Fri Feb  1 14:48:17 CET 2008
    root@dev.askozia.com:/usr/src/sys/i386/compile/ASKOZIAPBX_GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.86-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 268435456 (256 MB)
avail memory = 236441600 (225 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 8 Entries> on motherboard
pci0: <PCI bus> on pcib0
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xe000-0xe03f mem 0xd3100000-0xd3100fff,0xd3000000-0xd30fffff irq 11 at device 7.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: Ethernet address: 00:90:27:91:ef:b9
pci0: <display, VGA> at device 9.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
pci0: <multimedia, audio> at device 18.3 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xd3104000-0xd3104fff irq 11 at device 19.0 on pci0
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0501> can't assign resources (port)
Timecounters tick every 1.000 msec
i4btrc: 64 ISDN trace device(s) attached
i4brbch: 8 raw B channel access device(s) attached
i4btel: 8 ISDN telephony interface device(s) attached
i4bctl: ISDN system control port attached
capi: CAPI call control device attached, v2.10
i4b: ISDN call control device attached
usb0: 12Mbps Full Speed USB v1.0
md0: Preloaded image </mfsroot> 18143232 bytes at 0xc0a34a28
GEOM_LABEL: Label for provider md0 is ufs/MFSROOT.
uhub0: <(0x0e11) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
ihfc0: <HFC-2BDS0 128K USB ISDN adapter>
ihfc0: Attaching I4B controller 63.
ihfc0: Creating /dev/ihfc63.X.
ad2: 30MB < verB.65> at ata1-master PIO2
GEOM_LABEL: Label for provider ad2b is ufs/ASTERISK.
Trying to mount root from ufs:/dev/md0
GEOM_LABEL: Label ufs/MFSROOT removed.
Zapata Telephony Interface Registered on major 196
Echo Canceller: OSLEC
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
fxp0: Microcode loaded, int_delay: 1000 usec  bundle_max: 6
ztdummy: loaded

For pb14 it is'nt possible to record the boot-messages. So, I wrote the last messages at the boot-sccreen by hand:

md0: Preloaded image </mfsroot> 19267584bytes at 0x09f4c64
uhub0: ...
uhub0: ...
Trying to mount root from ufs:/dev/md0
**************************************************************************************
* FATAL ERROR
* The device that contains the configuration file ( config.xml) could not be found.
* AskoziaPBX cannot continue booting.
**************************************************************************************
.
.
.
The operating system has halted.
Please press any key to reboot.

[mcnobrain]

hello

i got the same error.. i tried it with a 32MB and 256MB card

[Michael]

Could you also post your dmesg information here like the last reporter?

[mcnobrain]

Here the dmesg output:

hostb0@pci0:0:0:   class=0x060000 card=0x00000000 chip=0x00011078 rev=0x00 hdr=0x00
    class    = bridge
    subclass = HOST-PCI
isab0@pci0:18:0:   class=0x060100 card=0x00000000 chip=0x01001078 rev=0x30 hdr=0x00
    class    = bridge
    subclass = PCI-ISA
none0@pci0:18:1:   class=0x068000 card=0x00000000 chip=0x01011078 rev=0x00 hdr=0x00
    class    = bridge
atapci0@pci0:18:2:   class=0x010100 card=0x00000000 chip=0x01021078 rev=0x00 hdr=0x00
    class    = mass storage
    subclass = ATA
none1@pci0:18:3:   class=0x040100 card=0x00000000 chip=0x01031078 rev=0x00 hdr=0x00
    class    = multimedia
    subclass = audio
none2@pci0:18:4:   class=0x030000 card=0x00011078 chip=0x01041078 rev=0x00 hdr=0x00
    class    = display
    subclass = VGA
ohci0@pci0:19:0:   class=0x0c0310 card=0xa0f80e11 chip=0xa0f80e11 rev=0x06 hdr=0x00
    class    = serial bus
    subclass = USB
rl0@pci0:20:0:   class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 hdr=0x00
    class    = network
    subclass = ethernet

Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p10 #0: Fri Feb  1 14:48:17 CET 2008
    root@dev.askozia.com:/usr/src/sys/i386/compile/ASKOZIAPBX_GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Cyrix GXm (299.75-MHz 586-class CPU)
  Origin = "CyrixInstead"  Id = 0x540  DIR=0x8244  Stepping=8  Revision=2
real memory  = 265814016 (253 MB)
avail memory = 233881600 (223 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 2 Entries> on motherboard
pci0: <PCI bus> on pcib0
isab0: <PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
pci0: <multimedia, audio> at device 18.3 (no driver attached)
pci0: <display, VGA> at device 18.4 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xe0003000-0xe0003fff irq 11 at device 19.0 on pci0
usb0: <OHCI (generic) USB controller> on ohci0
rl0: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xe0004000-0xe00040ff irq 12 at device 20.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0b:ab:05:6d:62
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: [FAST]
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounter "TSC" frequency 299748757 Hz quality 800
Timecounters tick every 1.000 msec
i4btrc: 64 ISDN trace device(s) attached
i4brbch: 8 raw B channel access device(s) attached
i4btel: 8 ISDN telephony interface device(s) attached
i4bctl: ISDN system control port attached
capi: CAPI call control device attached, v2.10
i4b: ISDN call control device attached
usb0: 12Mbps Full Speed USB v1.0
md0: Preloaded image </mfsroot> 18143232 bytes at 0xc0a34a28
GEOM_LABEL: Label for provider md0 is ufs/MFSROOT.
uhub0: <(0x0e11) OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
ad2: 244MB <TOSHIBA THNCF256MQG 3.00> at ata1-master PIO4
GEOM_LABEL: Label for provider ad2b is ufs/ASTERISK.
Trying to mount root from ufs:/dev/md0
GEOM_LABEL: Label ufs/MFSROOT removed.
Zapata Telephony Interface Registered on major 196
Echo Canceller: OSLEC
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
atapci0: <Cyrix 5530 ATA33 controller> port 0xf000-0xf00f at device 18.2 on pci0
atapci0: unable to map interrupt
device_attach: atapci0 attach returned 6
ztdummy: loaded
rl0: link state changed to UP

[Michael]

I seem to have overlooked a patch in the m0n0wall project which should resolve this (booting from Cyrix 5530 ATA controllers).

It's now been added and a test snapshot is available here:
http://downloads.askozia.com/pbx/snapshots/r812/pbx-generic-pc-r812.img

[mcnobrain]

I Tested the new release and every thing works fine now 

Thank you very much !!!!

[Minol-Pirol]

It works.

[Michael]

Great to hear!

Thank Manual Kasper from m0n0wall for pointing out the patch.